Articles, Blog

Understanding Anti-lock Braking System (ABS) !

Understanding Anti-lock Braking System (ABS) !

Nowadays an anti-lock braking system
is used in almost all modern vehicles. This system prevents accidents like this, where you lose control of the steering
as you apply the brakes. With ABS, you will be able
to steer the vehicle properly and it also reduces the braking distance. What is ABS? How is it able to prevent
accidents due to the braking? We will explore these
questions in this video. To properly understand ABS, we first need to understand
the principles of steering and braking. When you press the brake pedal, the brake pads on the wheel disks will
be activated and press against the disks, and this will stop the rotation
of the wheels. As the wheels stop, this causes slippage between
the road and wheels, and the vehicle stops due to this friction. Now let’s understand the steering mechanism. The whole steering mechanism is dependent on the simple principle of the wheels rolling. The wheels will always try
to avoid slipping on the road. So this means that the velocity of
the wheel at the contact point will always be zero. The wheels have two kinds of motion. They rotate on their axis and also
they move along the direction of the car. Due to these two kinds of motion,
they have two kinds of velocity: translational and rotational. For non-slip rolling conditions, the sum of the translational
and rotational velocities at the contact point should be zero. Just keep this simple principle in mind, and you will very easily be able
to understand the steering mechanism. In an automobile, all four wheels should be rolling at
all times to avoid the vehicle slipping. In fact, this simple rolling
principle is the reason why your car turns when
you turn the front wheels. Let’s examine this. Assume a hypothetical condition in which, even after turning the wheels,
the car carries straight on. In this case, the rolling velocity
will be inclined as shown, and the translation velocity
remains straight. Therefore, if you add up
these two velocities, the resultant velocity will not be zero. This will cause the car to slip. The only way to avoid this is by making
the translation velocity also inclined. This is possible only when the whole
car makes a turn as shown. When the car makes a turn at
the instantaneous center shown, all four wheels can satisfy
the condition of rolling. From this snapshot, you can
clearly see how the velocity at the contact point of all
four wheels becomes zero. Now, let’s analyze the steering
mechanism at the time of braking. Due to the brake pads being activated,
the wheels stop spinning. Even though the wheels are turned,
since they are not rotating, there will be no rotational velocity at all. In this case, the vehicle
does not need to turn as this has become like
a normal case of braking. The vehicle will no longer react to
the driver’s changes to the steering and will slide in a straight line
which can cause an accident. Apart from losing control of the steering, cars without ABS face another big issue, braking on surfaces with
different levels of traction. When the left and right wheels
are on different traction surfaces, applying the brakes will generate
different frictional forces on the wheels. This will produce torque, and the car
will go into an uncontrollable spin. Let’s see how ABS solves these issues. An anti-lock braking system is very simple. What ABS does is to prevent
the wheels from completely locking up. The ABS system includes speed sensors
attached to all of the wheels. When the sensors detect that
a wheel is about to lock up, a modulator unit partially releases
the brake pad on that wheel. This way, the wheels will be allowed
to spin intermittently during braking. You can immediately see the effect of this intermittent wheel rotation on steering. Here, the wheels will have
a rotational velocity component. This will definitely allow
the steering to function, and driver will be able to steer
the vehicle even during the braking. But the big question here is: How does the action of intermittently
releasing the brakes reduce the braking distance? To get an answer to this question, we first need to understand
how the coefficient of friction between the tire and the road
varies with respect to slip. In perfect rolling conditions, the value of the frictional
coefficient is nearly zero. However, when the wheel is 100% slipping,
sliding friction comes into play. You can expect the frictional values for
other levels of slippage to vary like this. But since rubber is a complex material which has strange behaviors during braking, the frictional coefficient between
the tire and the road varies as shown with respect to slippage. It has a peak value at
around 12% of slip ratio. And below and above this,
the frictional coefficient reduces. During breaking without ABS, the frictional coefficient
which comes into effect is predominantly sliding friction. However in ABS braking, the clever algorithm adjusts
the break pressure to keep the slip ratio near to 12%, where the frictional value
is at the maximum. This significantly reduces
the braking distance. Now back to the huge
instability issue of the cars. By intelligent electronic
braking distribution, which is a subsystem of modern ABS, one can overcome this issue very easily. An EBD yaw rate of the car and the relative slip of each
wheel is measured. Just by reducing the brake pressure
on the wheels with higher grip, we will be able to reduce the frictional
force produced by these wheels. This will keep the yaw torque and
the whole car under control. We hope this video gave you a clear
conceptual overview of the workings of ABS. And please, don’t forget to support
our educational activities on patreon. Thank you!

Tagged , , , ,

100 thoughts on “Understanding Anti-lock Braking System (ABS) !

  1. if you need to brake when cornering, there is added load to the amount of friction between the tyre and the road, how does the abs accommodate this added load?

  2. I have a VW Parati Crossover without ABS, so when an emergency braking situation comes I'll be fucked up?

  3. So you're saying the coefficient of friction increases as the friction becomes more kinetic? That doesn't make a lot of sense.
    Also if the coefficient of friction during perfect rolling is almost 0, then when the car is stopped, the coefficient of friction between the car and the ground is almost 0, which would cause 2 things:
    1. Accelerating would be near impossible, because you would start spinning the tyres immediately.
    2. Pushing the car around with the handbrake engaged would be really easy because it has no friction with the ground.

    From what I know, during perfect rolling the tyre has the most friction and that's where the ABS aims to place it

  4. Because I had already understood how abs works, I don't think if I showed this to my Mom she would understand a word of it, in fact, you went way "overboard" with your explanation, eg. You talked about most 'modern' cars, yet ABS was invented in the late 1920's for use on airplanes, and late 1960's and by mid 1970's saw implementation for cars, Yes, and without microchips, and all the complex stuff you talked about. Still a good video, but learning shouldn't have to be this complicated. P.S. ABS is for novices, that play with xbox, and their modern cars are all steered by wire. lol. thumbs

  5. Of course letting off the brakes until the moment the wheels resume rolling stops the vehicle the fastest, given maximum braking effort is transferred without interruption of ABS releasing brakes or sliding.

  6. This video really helped me because automobile engineering is a subject in my school and some of the things our teacher taught were unclear, but after watching this video, I understood it a lot better. Also, my exams are coming soon and this video helped me to recall my memory. So wish me luck!

  7. I understand it completely! People are devolving at such an incredible rate that they can no longer be taught how to drive a car

  8. Sir, you told" wheels try to avoid slipping" but how? will there be any constraint on tires? could you please explain the physics of tires and their friction behavior.

  9. How about its efficiency on loose surfaces? Rallycross cars really slide around, and its the fastest way on the track, otherwise they wouldn't do it

  10. I was driving today, and had to slam on my brakes to avoid a bicyclist that came in front of me. I felt my brakes slip. I knew my car had abs but didn’t know what it what or felt like. It concerned me. Thanks for teaching me something new.

  11. Add about front axles and and its type. Please add the video before 1st Dec (it will provide me a great help for my exam).

  12. Can i install an abs sensor on it's opposite side? For example installing a drivers side sensor on the passengers side. Will it have different connectors, or is there anything else that might prevent me from doing so

  13. I dont like abs break. You might be confusing that the break not activate. Especialy your are near in traffic light . You overpass the lane you cannot control exactly where you want to stop your car.

Leave a Reply

Your email address will not be published. Required fields are marked *