Articles, Blog

How To Make A “Car Hero” Key Box

How To Make A “Car Hero” Key Box


For this project, I’m going to show you
how to eliminate the fear and panic of losing your car keys, and the frustration of getting
locked out by your kids. Especially when your keys, are locked inside with them. Let’s start this project with a 45 lb. karabiner
hook magnet, and a bottle of kids vitamin gummies. Save the gummies for your kids because
all we’re really after here is the plastic container, and the reason I chose this bottle,
is because it’s fairly cheap, and the mouth is wide enough for a key fob, to slide in
and out without any problems at all. Now rather than making our own magnetic key
box, you might be wondering, “Why not just go to the store and buy a pre-made case instead?”.
The answer is that you could, but they aren’t big enough to store transponders and key fobs,
so they won’t work very well with newer vehicles. The magnets aren’t impressively strong either.
I tested the store bought version on a flat steel weight and found that the most it could
handle was 5 lbs … barely. One the other hand, you can find super magnets
at the hardware store, that claim to hold up to 45lbs. Now in practice, I found the most they’re
really good for is about 25 lbs. which is nearly half of what’s advertised. But despite
the inflated claim, you can still see they’re still at least 5 times stronger, and that
will make all the difference. Now to make a car hero key box, we’ll need
our magnet secured firmly to the lid of the bottle, and I found the easiest way to do
that is with a flat-head screwdriver and a propane torch. Of course if you don’t have
a propane torch, you can always use a bbq igniter instead. Get your screwdriver and carefully heat the
tip for a few seconds in the open flame so it gets good and hot, then quickly press it
into the top of the lid so it makes a hole that’s slightly offset from the center.
While it’s still hot, make another hole in-line with the first, and you should end
up with a nice clean slit right down the center. Now, when your screwdriver’s cooled down
a bit, gently pry at the edges of the bottle cap liner, and pop it out so you can modify
the underside of the cap. Heat the screwdriver again, but this time,
rather than poking all the way through the cap, carefully carve a channel out of the
inner plastic lining, around half an inch long on either side of the slit. Take your
time and do a good job, because it’s really important that you don’t burn into the yellow
part of the cap underneath. With this little channel carved out, go ahead
and unhook the karabiner from the magnetic base, so you can flip it over and press karabiner
clip down into the cap, locking it into place with the magnetic side facing up. Now if you look closely at the underside of
the cap, it should start to make sense how this is going to come together. Try hooking the karabiner back in place, and
you’ll most likely find there’s just barely enough clearance to get it lined up with the
hole. But with a little persistence, and some leverage from your screwdriver, you should
be able to pull it all the way through. It’s locked together pretty tight now, and that’s
really great, because it means there’s very little chance it’s ever going to come off
by accident. At this point, you’re pretty much done,
so go ahead and clip a spare set of keys onto the karabiner, and that’s it. You’ve got yourself a super strong, and
weather resistant, car hero key box. That’ll accommodate an emergency set of keys, with
room to spare. Now let’s go one step further and give it
a paint job. I thought it would be fun to try coating it
with some abrasion resistant truck bed coating. This stuff is normally used for lining truck
beds, but you can see it gives the bottle a cool textured look, that will help camouflage
it a bit, so it blends in better with where we’re going to hide it in a second. Spray a couple of coatings on the cap as well,
because it’ll help seal the gaps around the magnet, and make the whole thing water
resistant. Now since your vehicle is built on a steel
frame, your super strong key box will stick just about anywhere you want. And if you look
around for awhile you’ll see hundreds of little nooks and crannies where you could
hide it, so pick a place that works best for you, and your piece of mind. Now the next time you walk out to your car
and realize your keys are missing, you don’t have to worry about calling a friend for a
ride, or breaking a window to get in. Instead, simply reach for your emergency key
box, and a clean set of spare keys,will be waiting there, ready to help you out. Just like that you’ve dodged a potentially
embarrassing situation, and emerged a car hero instead. Saving you time, money, and maybe even your pride as well. Well now you know how to convert a magnet
and plastic bottle into a car hero key box. That’s over 5 times stronger than store
bought brands, and much more convenient to use. By the way, try throwing a few hand wipes
in there as well. This way if you get a bit dirty in the process, you’ll have something
handy, to wipe yourself clean. That’s it for now. If you like this video,
perhaps you’ll like some of my others. Check them out at www.thekingofrandom.com

Tagged , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,

100 thoughts on “How To Make A “Car Hero” Key Box

  1. Man I miss these type of videos. I hope once they start making videos again that they will do stuff like this again

  2. You will always find a way in our hearts .you were took to soon .you will always be in are heart .you will be missed .

  3. I know I'm late but theres a saying that goes "The goal in life isnt to live forever, its to make things that do"

  4. If you turned the screw driver in a full circle when he entered it into the cap…. the vid would of turned into how to make a grav lol

  5. YouTube's recommending me his videos, more than usual. Sad to see such a legend pass, will always be with us in our hearts.

  6. “ hey guys this is the end of the video but not the end of our adventuress”
    that one hit me for sure 😢

  7. If I want a hidden spare key, I wouldn't want the fob on it too. It's very expensive if it goes missing. So you don't need a big bottle with more chance of dropping when hitting bumps on road

  8. The reason it could “only hold 25 lbs” might have something to do with the fact that its point of contact was on the side of the weight where it has curvature. Reducing the surface area it can grab onto

  9. Bruh, this sucks. I've watched his vids since the age of 8, I always wanted to be like him… and make things. My first ever video was the Yellow Rocket one. RIP, you will be in all of our hearts.

Leave a Reply

Your email address will not be published. Required fields are marked *