Articles, Blog

Doing This Will Save You Thousands in Car Repairs

Doing This Will Save You Thousands in Car Repairs


rev up your engines, today I’m going to
show you how you can save thousands of dollars fixing your car, now I’ve learned
a lot of tricks over the years I’m going to share quite a few of them,
now the first trick has to do with these expensive headlight assemblies, often as
they age the seals go bad or they get a little rock chips and then
water gets inside and it starts condensing inside, now as they age the
plastic gets brittle it’s often hard to figure out where water is coming from
and since these things can be really expensive, in the case of this Porsche
these little plastic headlight assemblies, hey they cost almost $1,100
a piece, so if you can get rid of the water and keep it from building up, you can
save yourself a lot of money there, and here’s trick, a drill, now in this case
I have the assembly off the car, but a lot of times you can get under the car
you can drill hole in the bottom of the assembly without removing it. sometimes
you need a long drill bit. I got one this
long that I use super long for getting in holes, but once you drill a hole
down here in the lowest point, now there’s a hole, any water gets in it’s
gonna drain out that hole, now this particular one has halogen headlamps,
halogens get relatively hot, which actually is a good thing if you get
water inside, because the heat will vaporize any water vapor that’s left, and
it’ll just vent out the hole, you don’t have to worry about getting the old
stuff out if any more drips in, I have literally done this to hundreds of my
customers cars, especially when they have an older car the plastic is cracked, your
never gonna be able to figure out where the
leak is anyways, so all you gotta do is drill a hole in the lowest point and any
water gets in it’s gonna drip out there, it’s not like you’re driving a car under
water and it’s got to be sealed perfectly, and of course you can do this
hole drilling technology any part of the car if water’s building up inside
something, just realize you always want to drill a hole on the bottom on the
lowest point, so the water will always come out then
and sure if you go underwater some water will get in, but hey we’re not driving
submarines here, now the next trick has to do with fixing oil leaks on your car, now
I know some people are gonna scream, oh snake oil Scotty you selling snake oil, well
you know I thought the same thing, when I started using this stuff four decades
ago, I thought what can stuff in a bottle do, well it really shocked me, to begin
with as you can see it’s a clear polymer it looks just like water, it doesn’t have
any suspended solids that could clog things up in whatever system you use it
in, when I started testing that stuff out four decades ago, I thought okay I had a
hydraulic jack for lifting up cars it was leaking fluid all over the place, I
poured a couple ounces of that stuff in with a hydraulic jack oil, I have
to say it really shocked me, because the next day when I use that Jack and jacked
it up, instead of a puddle being under it from hydraulic fluid leaking, there
was nothing, I ended up using that jack for years and it didn’t leak anymore
and being a polymer can mix of all kinds of fluids, the best use I find is, let’s
say you have a rear main engine seal leak, or a front main transmission leak
guess what you have to pull out the engine to get to the seal, or pull out
the transmission to get to either the back engine seal or the front
transmission seal, and then of course is gigantic money, big money to pull out of
an engine or an automatic transmission, I’ve used this stuff on hundreds of cars
over the years, now sometimes yeah it won’t stop the leak, because if the seal
is so shot that pieces have actually come off, hey no sealer is gonna fix that
but it often works cuz many oil seals they’re round and on the inside of
that seal there’s a spring that holds the lip onto the shaft, and if the sealer
makes that lip more supple the spring squeezes it in more and it stops leaking
now in the olden days, guys used to cheat when they’re selling the car and they do
stuff like throw sawdust in an engine to keep the seal from leaking, or even worse
put brake fluid in it, because brake fluid swells up rubber
and it will stop it from leaking but only for a short period of time, then
what happens is, after they swell up they shrink even further and then they
leak even more, in the past I’ve had customers buy cars that somebody had
done that, and then they changed the oil and all of the sudden it starts leaking oil
like mad, and I say aw somebody must have put brake fluid in it to swell the
seals to sell it to you, and now you’re gonna have to pull the engine out and put
new seals in it, the at 205 doesn’t work that way, it’s a polymer it rejuvenates
the seals it doesn’t make them get all big and swollen, so I’ve been using
this stuff for 40 years and it still amazes me that somebody could come up
with such an idea that would work so well in most cases, I’ve used it to fix
engine seal leaks, transmission seal leaks, rear end seal leaks, I’ve even used
in power steering systems, but there you have to realize something, since it’s a
polymer there’s no solid suspended in it, it’s not gonna clog up your power
steering system, but realize power steering system, hey they have like 1500
psi pressure inside that system on the high side on the pressurized side, and
often nothing is going to seal a leak in a system that’s got 1,500 pounds per
square inch pressure trying to squirt it out, now another thing that can save you
thousands on your car repairs is this jb weld quick, it’s a two tube steel epoxy
system, and man you can see I’ve got the big ones they make a little bitty ones
too but I use it all the time so I buy the big package, it’s a simple system you
got steel and you got the hardener, you just squeeze equal amounts on it on a piece
of cardboard, mix it up, and then it’s an
epoxy that can seal a lot of stuff with, your probably not gonna believe
this next story but it’s real, the biggest job I ever fixed with one of
these was a Volvo engine, it was leaking coolant out of the head, I could see a
crack, so I did a two-part process I used mr. drill again, and each end of the
crack I drilled tiny little holes, that’s to keep the crack from spreading, then I
mixed up the epoxy, got a putty knife and I put it in each hole, pushing it into
the crack and let it dry, now in this case you gotta use patience, you might
think, Oh Scotty he doesn’t seem very patient, well I’m usually not, but when I
used stuff I have to turn my brain down a
little and realize, you got in some patients,
it’s called JB weld quick because it’s fast it’s fast, it sets in four minutes, but
it fully cures and hardens after four hours
and me I’ve learned, I let it sit for 12 hours before I use the stuff again
in the case of the volvo head that was leaking, I let it sit for 12 hours
overnight, and the next day I started it up and ran it for half an hour drove it
around and checked, no coolant was coming out, and the customer drove that car for
years longer never leaked there again, which really amazed me I didn’t think, hey is
is this stuff really gonna work on something like that, but it did so if you
use it on things that aren’t all that stressful, like this headlamp assembly on
my old celica you can see there’s all a goo there that’s holding the headlight
together, now when I bought this car years ago from a customer, this fender
was all smashed in because she’d been in an accident, and it had broken the
headlight assembly, well hey I only paid 350 for the car, so I’ll be cursed I’m
gonna spend more than that on this Toyota headlight assembly, I just jb weld
it together so it bolted on and didn’t wobble anymore
and yeah I’ve got a really sloppy job but who cares, look the hoods closed now
of course you can do a much neater job than that, but I learned one thing with
epoxies, the more the merrier so if you have a whole bunch and it’s really thick
it’s gonna have more tensile strength, so if it’s something that you don’t see
when you’re driving the car, who cares if it’s kind of blotchy, it’s bigger and
it’s gonna hold together because there’s more epoxy and a stronger bond in that
area, so sometimes messy is better than neat
just like my garage behind me, so really this jb weld I’ve been using this stuff
for years and years and years, just heed my warning, even though it says quick and
it sets in four minutes, wait at least four hours before you start operating a
vehicle, because you’ll want the stuff to set and cure entirely, not just be dry to
the touch on the top, so now you know three ways that you can save thousands
of dollars fixing your car, and if it ever stops raining I can go back to
fixing some of my customers cars, so if you never want to miss another one of my
new car repair videos, remember to ring that Bell!

Tagged , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,

100 thoughts on “Doing This Will Save You Thousands in Car Repairs

  1. ⬇️ Things used in this video:

    1. ATP Reseal: https://amzn.to/2XfxuNG

    2. JB Weld: https://amzn.to/2Vc24pB

    3. Common Sense

    4. 4k Camera: https://amzn.to/2HkjavH

    5. Camera Microphone: https://amzn.to/2Evn167

    6. Camera Tripod: https://amzn.to/2Jwog8S

    7. My computer for editing / uploading: https://amzn.to/2uUZ3lo

    ⬇️Scotty’s Top DIY Tools:

    1. Bluetooth Scan Tool: http://amzn.to/2nfvmaD

    2. Cheap Scan Tool: https://amzn.to/2D8Tvae

    3. Professional Socket Set: http://amzn.to/2Bzmccg

    4. Wrench Set: http://amzn.to/2kmBaOU

    5. No Charging Required Car Jump Starter: https://amzn.to/2CthnUU

    6. Battery Pack Car Jump Starter: http://amzn.to/2nrc6qR

    🛠Check out the tools I use and highly recommend ► https://goo.gl/rwYt2y

    🔥Scotty Shirts and Merch ► https://goo.gl/pTAeca

    Subscribe and hit the notification bell! ► https://goo.gl/CFismN

    Scotty on Social:

    Facebook ► https://www.facebook.com/scottymechanic/

    Instagram ► https://www.instagram.com/scotty_the_mechanic/

    Twitter ► https://twitter.com/Scottymechanic?lang=en

  2. Hey Scott, first off thank you for all your videos, and the humor that you throw in. I'm a newer subscriber and have watched most of them,,along with doing a ton of research online. I'm building a 94 grand cherokee laredo 4×4 with a 5.2 magnum for my sons first car,,,200K+miles, ford 8.8 rear, 2.5 inch lift, etc.. Its been neglected forever so needless to say everything has been a chore, and every job has taken 2-3 times longer that usual. Long story short, changed the black tar and put in new oil 5-30, within 2 hours , poof- smoke out the tailpipe. Anyhow, I'm hoping you can elaborate on the AT- 205?, I've bought it but am reluctant. Maybe a whole video about it? Guaranteed its the valve seals.
    Note- I drained the new oil GTX 5-30 HM after only about an hour of running it and it was BLACK, just as black as my usual 3k mile oil changes on my newer ford. I was amazed, chalked it up as a "cleaning" and then added M1 10-40 HM ,,no result to report yet as I have to put in new PCV valve (in mail as I write this). Thank you,
    Pete Kaz

  3. I used jb weld on my wife’s passenger mirror. She it a wall and the hole thing broke off and was hanging from the wire and it’s fixed now haha

  4. Myth has it Scotty doesn't wear sunglasses, He has 2 Black eyes from trying too steal Celica parts daily, He also uses JB weld to draw a line down to his ears so it looks real

  5. fixes leaks on A/C pipes, smear it on and wrap rubber inner tube around pipe secure with ties and more weld, job done,

  6. Marine-Tex is better than JB Weld. You guessed it, used on boats and in underwater applications.

  7. @ 3:01, Scotty's a 'lefty' lol. Great videos sir, I enjoy them! Keep up the work! Did my own timing belt by watching your vids. '09 Kia Sportage… saved me $800. No valve-crash yet!
    Here's hoping Dayco Timing Belts are good!

  8. You didn’t mention the name of “this stuff” for stopping leaks and I can’t see the label. What is it please?

  9. Sorry saw the link. My bad. Just cleaned my air flow sensors and throttle body. Thanks for the great tips!I’ve got this friend and he’s a mechanic and he says to…….

  10. Put a hollow metal ball between carb and intake manifold atomizes and vaporizes gas doubles gas mileage and cleans up emissions this is possibly how Poque did it

  11. for a moment there I thought you were gonna drink that!… lol… ' ; ) …keep it comin' yer learnin' me up real good…

  12. Hey Scotty I see leak near water pump and also see some engine oil leaks at the same spot in my tarago 92 can I use something to stop leak please? Thanks

  13. I am 70 yrs old and the back board will let me drive to fishing trips,I could really use that as I have an arthetic back. Thanks

  14. had to drill my '86 300ZX as the seatbelt was getting wet from rain leaking into the side well. Stopped the water build up and never a wet seatbelt again!.

  15. Hi Scotty – RE: ATP AT-205 Re-Seal – I remember you previously said to be careful not to put thick oil in to help leaks stop or slow because some engines have to push fine oil through small lubricating holes – will this ATP AT-205 Re-Seal cause any problems with oil getting into certain small oil hole parts of my engine? My Main engine seal is leaking – you said it might seal that – but might it seal my timing chain covers / tensioner seal and tappet cover gasket leaks which are leaking badly? ( – Really don't want to spend much repair money on a Ford Falcon 2002 6cyl with 310,000 klms) – thanks

  16. Because it sets so fast that means you mope around putting it on I've found that you can't mix up bunch of it at a time but with some patience it works very well JB weld that is ha ha ha.

  17. @2:15 Scotty Kilmer "We're not driving submarines here."
    Me: "Challenge Accepted." 😑
    I've taken my 2000 Land Rover Discovery II through at least four feet of water, using a snorkel of course, and had a great time. Of course I got water in my rear UPPER (I can't figure this one out!) light assemblies, but the lower ones stayed water tight.. didn't even THINK to put holes at their bottoms to drain the water, I was just going to replace them with jon cracked lens assemblies.

  18. I broke a corner on a intake manifold on a mustang. It was a cast iron intake and I over tighten it. I put JB weld on it and waited until the next day and put it back on. Never had any trouble with it.

  19. clean up that f-ing pig pen After seeing yer video I wouldnt bring you a bicycle to have worked on..SMDH

  20. JB Weld is the best! I fixed a timing cover that a loose pulley chewed through with it. It's still holding years later no leak!

  21. I absolutely hate when my rear-end leaks, thanks the doctor would have charged me an arm and a leg just to fix the rear-end….

  22. You have to make an air intake hole at the top too. Cause it doesn't drain because it maybe leaky but it most likely super small. So u need a air hole

  23. Awesome! Thanks for the info. You should wear a white lab coat and mess up your hair like you stuck your finger in a light socket for the mad scientist look! I think that would complete your character lol…your brilliant!

  24. Would you recommend using atp-205 as preventive maintenance on a 5yr old/70k miles car, or use it only if there is a visible leak?

  25. ATP reseal saved me a ton of money! No joke it works! Rear main was leaking. Not anymore! Thanks Scotty.

  26. mechanics recommend all kinds of things for your own good…who recommends to the mechanic about their own car$?

  27. He mentions sawdust in an engine ti stop leaks and break fluid for other places, but I didn't see anything about putting a banana in a standard transmission or a rear end to stop gear whine.

  28. Great video.
    Personally, i myself have been retaining water.
    I drilled a hole in my toe…(lowest point as per your instructions).
    …I'll let you know the results.

  29. Imagine, Scotty turning his brain down. Just how far down is the question I have. Scotty under the canopy with his brain turned down, waiting for the rain to stop, as he counts his money.

  30. What your thoughts on Miracle Seal Epoxy?

    I have used on exhaust systems when you have holes or the hanger broke Or it broke at the catalytic converter where it bolts up around the seam that’s always welded.

    You normally don’t run into this problem in Texas but northern states do.

  31. Would this work in places with heavy snow?

    Not driving a submarine but sure am driving a snow mobile in Minnesota winters.

  32. Very good. I haven't found you in a long time. Wow, you haven't changed at all. I always learn something valuable from watching and listening to you. I used to see you on my local Houston tv channel but unfortunately, no more. Now, I have subscribed and I can follow you from now on. I do have a question but this is a comment section so I will look around for the place to ask questions. Thanks again.

  33. Jb weld works best in layers, each one dried sufficiently, then scuffed lightly with 80 grit then blow dust and dab with paper towel wetted with 90 iso alcohol

Leave a Reply

Your email address will not be published. Required fields are marked *